-
Test and Drain Valve
The test and drain valve complies with NFPA13 sprinkler systems. Inspector’s test and drain unit w/on-off unit with brass sight glass. Female NPT inlet and outlet cast brass valve.
View Product Datasheet
QR 595.00View Options -
-
Cylinder Mounting Bracket
Vertical bracketing of the PCL-160, PCL-300 and PCL-460 is provided by the Model MB-15 bracket kit . Vertical bracketing of the PCL-600 is provided by the Model MB-1 bracket kit . These kits must be ordered separately with each cylinder/valve assembly. Cylinder installation instructions are provided in the installation section of this manual.
- Cylinder Bracket
- These kits must be ordered separately with each cylinder/valve assembly
- Cylinder installation instructions are provided in the installation section of this manual.
View Product Datasheet
QR 262.00 – QR 275.00View Options -
Nozzle
Nozzles have been developed for appliance, plenum, and duct applications. All nozzles have a specific flow point value and are supplied with metal blow-off caps to prevent clogging. Each nozzle is stamped with the model number.
View Product Datasheet
QR 145.00 – QR 154.00View Options -
Agent Cylinder With Valve
The cylinder is manufactured, tested, and meets DOT requirements. Cylinders come pre-filled with extinguishing agent and are charged with dry nitrogen to a pressure
- Meets the requirements of the Building Officials and Code Administrators (BOCA)
- Meets the requirements of the International Building Code (IBC)
- Approved by the City of New York Material and Equipment
View Product Datasheet
QR 2,445.00View Options -
Bladder Expansion Tank
Intended for use in hydronic heating systems, these tanks accept the expanded volume of hot water keeping the system pressure below the relief valve setting, thus preventing dangerous pressure build-up.
View Product Datasheet
QR 12,200.00 – QR 13,500.00View Options -
Roof Exhaust Downblast
FCS -D (Direct drive) & FCS -B (Belt drive) fans are ideal for general purpose exhaust applications including bathrooms, garages, general kitchen areas, offices, churches, dormitories, factories, large warehouses, and other relatively clean air applications. They feature a weather-resistant, seamless spun aluminum housing which works in conjunction with a patented wheel design and deeply spun inlets to provide smooth quiet airflow through the ventilator. The centrifugal wheels are aluminum, non-overloading, backward inclined, robotically welded, and dynamically balanced
View Product Datasheet
-
Plate Mounted Axial Fans
The QCM series are axial fans suitable for application on wall or panel in residential, commercial and industrial building.
View Product Datasheet
-
Gravity Shutters
Gravity Shutters avoids heat loss and entry of wind, rain, and birds. The fins of the shutter are opened by the airflow when the fan is working and they close down by gravity when the fan is switched off.
View Product Datasheet
QR 295.00View Options -
-
Centrifugal Roof Extractors
Centrifugal roof fans are designed for direct or ducted ventilation in residential, commercial, and industrial buildings. they are designed for easy installation, high-efficiency low noise levels. The motor is outside the airflow, this allows the fan to exhaust clean or slightly dusty air with temperature
View Product Datasheet
QR 2,296.00View Options -
Pressure Independent Control ...
FLOWCON PRESSURE INDEPENDENT CONTROL VALVE, FIXED FEMALE BY FEMALE THREADED, PRESSURE/TEMPERATURE PLUGS (STANDARD) HIGH FLOW
The Flowcon PICV is designed as a 3-in-1 solution combining a full stroke modulation control valve, an automatic balancing valve, and a differential pressure control valve
View Product Datasheet
-
Centrifugal In-Line Fans Roun...
The AXC LINE-METAL is a series of centrifugal in-line fans with the advantage, typical of axial fans, to convey air along the same axis of the impeller
View Product Datasheet
QR 372.00View Options -
Inlet Cone
It allows a higher fan efficiency in case of installation with an inlet or outlet not ducted. Manufactured in steel sheet, with one flange according to UNI ISO6580 – EUROVENT to be fitted to the CC fan, and an aerodynamically shaped bell mouth, with fixing holes for a protection guard Protected against atmospheric agents by epoxy paint.
View Product Datasheet
-
Bye-Pass Assembly
For either system by-pass application, Flowcon recommends a combination of automatic/dynamic balancing and 3-way control with focus on indoor climate and reduced energy consumption FLOWCON FCU LINK WITH BYPASS ISOLATION VALVES, IVC STRAINER, AND FLOWCON PICV FIXED FMXFM WITH P/T PLUGS, SS FLEXIBLE CONNECTOR & INSULATION
View Product Datasheet BY-PASS ASSY
-
Ultra-Slim Wall Axial Fans
To exhaust air directly to the outside or into a short length ducting (max 3 m length). Suitable for toilets, bathrooms, WC’s, shower-rooms, utility rooms, and kitchens
View Product Datasheet