-
U Strap
Material: Steel
Function: Designed for supporting pipe runs from strut supports.
Approvals: Underwriters Laboratories Listed for B2400-3/4″ thru B2400-8″. Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 26 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 26.
Finish: Electro-Galvanized.View Product Datasheet
QR 37.80 – QR 44.80View Options -
U Bolt with 4 nuts
Heavy-duty U-Bolts designed to grip, guide or support plain and insulated pipes. Supplied complete with four nuts. Also available with EPDM sleeves.
View Product Datasheet
QR 8.65 – QR 17.29View Options -
Swing Check Valves -WEFLO
Swing Check Valve
- Complies with AWWA C508 clear waterway design
- Seating type is the resilient material to bronze seat construction
View Product Datasheet
QR 465.00 – QR 2,245.00View Options -
Test and Drain Valve
The test and drain valve complies with NFPA13 sprinkler systems. Inspector’s test and drain unit w/on-off unit with brass sight glass. Female NPT inlet and outlet cast brass valve.
View Product Datasheet
QR 865.00View Options -
Breeching Inlet
Breeching inlets are installed outside the building or any easily accessible area in the building for fire brigade personnel to access the inlet. This inlet is used by the fire brigade personnel to access water. It is normally dry but is used to pump water by charging using fire fighting equipment.
View Product Datasheet
QR 614.24View Options -
Pressure Switch
The Potter PS10 Series Pressure Actuated Switches are designed for the detection of a water flow condition in automatic fire sprinkler systems of particular designs such as wet pipe systems with alarm check valves, dry pipe, preaction, or deluge valves.
View Product Datasheet
QR 276.00View Options -
Tamper Switch
The OSYSU is used to monitor the open position of an OS&Y (outside screw and yoke) type gate valve.
The Model PCVS is a weather proof and tamper resistant switch for monitoring the open position of fire sprinkler control valves of the wall and yard post indicator and butterfly types
QR 333.00 – QR 340.00View Options -
OS and Y Gate Valves
Mueller 2300 Series Resilient Wedge Gate Valves are intended for use in potable water distribution or fire protection systems.
- UL 262 Listed and FM 1120/1130 Approved and certified to ANSI/NSF 61 & 372
- Epoxy Coated interior and exterior surfaces
- Outside Screw & Yoke (O.S.&Y)
- Adjustable packing
- Rubber encapsulated iron wedge
- Hand wheel – open left or open right
View Product Datasheet
QR 1,235.00 – QR 1,385.00View Options -
Swing Check Valve – KEN...
Kennedy Swing Check Valves are used to ensure flow in one direction.
- Used to ensure flow in one direction
- Disc is also Self Adjusting
- Minimizing wear and corrosion problems.
- UL & ULC Listed, FM Approved
View Product Datasheet
QR 1,420.19 – QR 2,882.00View Options -
Pressure Reducing Valve
Cla-Val 90-21 Pressure Reducing Valves are indispensable in any fire protection system.
- Globe or Angle Pattern
- Proven Reliable Design
- Available in Cast Bronze, Ductile Iron and Cast Steel
- Accurate Pressure Control
- In Line Service
- Grooved Ends
View Product Datasheet
QR 4,266.00View Options -
Elbow Malleable Iron
Elbow are used to change the fluid flow direction. It is used to connect two pipes with same or different nominal diameters, and to make the pipe and thus the fluid direction turn to a certain direction of 90 degree.
View Product Datasheet
QR 6.80 – QR 175.00View Options -
Butterfly Valve Grooved End
The TYCO Models BFV-300 and BFV300C Grooved End Butterfly Valves are indicating type valves designed for use in fire protection systems where a visual indication of open or closed valve condition is required
- Designed for use in fire protection systems
- UL and ULC Listed
- FM Approved
View Product Datasheet
QR 891.76 – QR 1,652.00View Options -
Grooved Check Valve
The TYCO Model CV-1F Grooved End Swing Check Valves are compact and rugged swing-type units that allow water flow in one direction and prevent flow in the opposite direction.
View Product Datasheet
QR 573.00 – QR 588.00View Options -
Water Flow Switch
The Potter VSR is a vane-type Waterflow switch with a non-corrosive insert for use on wet sprinkler systems.
- The Potter VSR is a vane type water flow switch with non-corrosive insert for use on wet sprinkler systems.
- It is UL Listed and FM Approved for use on steel pipe.
- Non – corrosive sleeve factory installed in saddle
View Product Datasheet
QR 395.00 – QR 565.00View Options -
Upright Sprinkler
The TYCO Series TY-B, 5.6 K-factor, Upright (TY315) Sprinklers are standard response, standard coverage, decorative 5 mm glass bulb type spray sprinklers designed for use in light, ordinary, or extra hazard, commercial occupancies such as banks, hotels, shopping malls, factories, refineries, and chemical plants.
- All hazard
- Discharges a hemispherical water spray pattern in the area beneath the sprinkler
- Small frame, narrow profile bulb
- Designed for use in light, ordinary, or extra hazard, commercial occupancies such as banks, hotels, shopping malls, factories, refineries, chemical plants, etc.
View Product Datasheet
QR 22.30 – QR 24.40View Options -
Fire Alarm Bell
A fire alarm is a unit made of several devices to warn people about a possible fire, smoke, or carbon monoxide occurrence in the area of coverage
- Thermoplastic Base
- High dBA Sounds Output
- Low Power Consumption
- Quick And Easy Installation
View Product Datasheet
QR 177.00View Options -
Loop powered Siren
Loop powered and controlled sounder for Securiline extended.
- 3 Signal tone (DIN 33404, Slow Whoop and 990 Hz pulsed)
- Signal tone controlled from the FACP depending on the event
- Configurable volume high/low
View Product Datasheet
QR 315.00View Options -
Sidewall Sprinkler
The TYCO Series TY 5.6 K-factor, Horizontal Sidewall Sprinklers are standard response, standard coverage decorative 5 mm glass bulb type spray sprinklers designed for use in light and ordinary hazard, commercial occupancies such as banks, hotels, and shopping malls.
- Light hazard/Ordinary hazard
- Small frame
- Unique deflector design of the horizontal sidewall sprinkler results in smaller profile
- Designed for installation along a wall or the side of a beam just beneath a smooth ceiling
- Water discharge is directed primarily outward and downward in a quarter spherical pattern
- Sidewall sprinklers are often used in lieu of standard pendent or upright sprinklers due to building construction, economic considerations, or aesthetics
- Special deflector on the vertical sidewall sprinkler allows it to be installed in either a pendent or upright position
View Product Datasheet
QR 35.00View Options -
Swinging Hose Reel
Side plates red epoxy powder finishing Threaded Inlet connection Side plates available in stainless steel
- Side plates red epoxy powder finishing
- Threaded Inlet connection
- Side plates available in stainless steel
View Product Datasheet
QR 765.00View Options -
Replacement Break Glass
Double Action Stations (Breakglass) requires the operator to strike the front-mounted hammer to break the glass and expose the recessed pull lever. The pull lever then operates as a single action station.
- Replacement break glass
- Non-Coded, Non-Addressable Manual Stations; 2099 Series Single and Double Action Operation
View Product Datasheet
QR 6.36View Options -
-
Riser Clamp
Riser clamps provide a safe and effective means of ensuring lateral stability while permitting axial thermal expansion & contraction when installed as pipe guides. Rugged two-part clamps, suitable for installation as rigid supports or guides for the plain or insulated vertical pipe.
View Product Datasheet
QR 14.50 – QR 39.76View Options -
Rubber Support Inserts (RSI)
A convenient and effective means of preventing the crushing of insulation at pipe support points of chilled water, condenser water, and domestic hot/cold water installations. Available for any pipe size and insulation thickness.
View Product Datasheet
QR 2.29 – QR 247.95View Options -
Cylinder Mounting Bracket
Vertical bracketing of the PCL-160, PCL-300 and PCL-460 is provided by the Model MB-15 bracket kit . Vertical bracketing of the PCL-600 is provided by the Model MB-1 bracket kit . These kits must be ordered separately with each cylinder/valve assembly. Cylinder installation instructions are provided in the installation section of this manual.
- Cylinder Bracket
- These kits must be ordered separately with each cylinder/valve assembly
- Cylinder installation instructions are provided in the installation section of this manual.
View Product Datasheet
QR 276.00 – QR 290.00View Options
- ALL PRODUCTS
- FIRE FIGHTING & FIRE ALARM
- HVAC & PLUMBING
- INSULATION MATERIALS
- AIR OUTLETS & DAMPERS
-
Grilles & Diffusers
- Egg Crate Grilles (Model: KECG)
- Door Grille (Model: XNSA)
- Spot Diffuser (Model: SPD)
- Jet Diffuser (Model: KDJ)
- Linear Slot Diffuser (Model:…
- Double Deflection Grilles (M…
- Exhaust Grilles (Model: KX3HD)
- Circular Diffuser (Model: KCM)
- Disc Valves (Model: KDV)
- Square Diffusers ( KDF series)
- Single Deflection Grilles (Mo…
-
- BROWSE BY BRANDS
-
- RATE US
- POPULAR
BRANDS
-
Refrigeration Copper Coils
Brand: IUSA Cambridge Lee
Copper Pipes & Coils manufactured to ASTM B743 standards are suitable for gas applications and other high-pressure refrigerants.
Buy nowIsoline Pipe InsulationBrand: K-Flex Isoline
Isoline is a high-quality rubber insulation which is a closed-cell tube insulation product used to prevent condensation on piping applications.
Buy nowWall Split Air ConditionerBrand: Ruud
Developed with environment friendly R410A refrigerant. R410A refrigerant is highly efficient and has an Ozone Depletion Potential (ODP) of 0.
Buy now
-