-
Water Flow Switch
The Potter VSR is a vane-type Waterflow switch with a non-corrosive insert for use on wet sprinkler systems.
- The Potter VSR is a vane type water flow switch with non-corrosive insert for use on wet sprinkler systems.
- It is UL Listed and FM Approved for use on steel pipe.
- Non – corrosive sleeve factory installed in saddle
View Product Datasheet
QR 342.00 – QR 435.00View Options -
Pressure Switch
The Potter PS10 Series Pressure Actuated Switches are designed for the detection of a water flow condition in automatic fire sprinkler systems of particular designs such as wet pipe systems with alarm check valves, dry pipe, preaction, or deluge valves.
View Product Datasheet
-
OS and Y Gate Valves
Mueller 2300 Series Resilient Wedge Gate Valves are intended for use in potable water distribution or fire protection systems.
- UL 262 Listed and FM 1120/1130 Approved and certified to ANSI/NSF 61 & 372
- Epoxy Coated interior and exterior surfaces
- Outside Screw & Yoke (O.S.&Y)
- Adjustable packing
- Rubber encapsulated iron wedge
- Hand wheel – open left or open right
View Product Datasheet
-
Pipe Insulation – Aluglass Faced
KIMMCO-ISOVER’s produces a wide range of glass wool-based pre-formed pipe sections; designed specifically for the insulation of HVAC pipework.:
Performed sections of glass fibers bonded with a heat-resistant resin, free from the shot and coarse fiber, light, damage-resistant, easy to handle, cut, and fit. The sections are split along their lengths to provide a hinge for ease of fitting. Aluglass facing ensures zero water vapor permeability, puncture resistance, and eliminates the need for external weather protection
View Product Datasheet
QR 11.50 – QR 125.00View Options -
Pipe Insulation – FSK Faced
KIMMCO-ISOVER’s produces a wide range of glass wool-based pre-formed pipe sections; designed specifically for the insulation of HVAC pipework.:
Faced with FSK – Pipe sections, with a factory-applied reinforced Aluminum foil covering (FSK) incorporating an overlap. Performed sections of glass fibers bonded with a heat-resistant resin, free from the shot and coarse fiber, light, damage-resistant, easy to handle, cut, and fit. The sections are split along their lengths to provide a hinge for ease of fitting.
Standard length: 1.2 MTR
View Product Datasheet
QR 14.00 – QR 195.00View Options -
Tamper Switch
The OSYSU is used to monitor the open position of an OS&Y (outside screw and yoke) type gate valve.
The Model PCVS is a weather proof and tamper resistant switch for monitoring the open position of fire sprinkler control valves of the wall and yard post indicator and butterfly types
-
Standard Air Louvers Model FAL
KMC Air Louvers are designed for both intake and exhaust air service for commercial & Industrial applications.
The fresh air louver is used to supply fresh air to the buildings or Air Handling Units (AHU).
Louvers are designed and manufactured for use in external applications.
Blades are fixed and at 45deg to protect against ingress of rain water.
View Product Datasheet
QR 48.00 – QR 209.00View Options -
Pressure Independent VAV unit...
KSQ terminals are AHRI Certified and are tested in accordance with AHRI Standard 880.
Optional factory installed electric heaters and integral sound attenuators for ultra-quiet performance are also available .
Note: The unit is supplied as a VAV box only . Controller and actuator to be provided by contractor .
View Product Datasheet
-
Curtain Fire Damper (UL 555 &...
The fire damper is intended to restrict the passage of flame; it shall consist of UL listed fusible link rated to 165˚F which shall release the curtain blades in the event of fire. The standard installation requires that the damper is positioned so that the closed plane of the blades is within the fire rated masonry/concrete barrier.
For non-standard construction & for more details consult our sales team.
QR 148.25 – QR 424.00View Options -
By-Pass VAV unit (Model: KME)
By-pass VAV terminals consist of a single primary air damper that shall proportion the total primary air through the terminal to either the ceiling plenum or the space as dictated by the space thermostat demand. These units are available with various casing materials & treatments with factory mounted actuators as required.
Note : The unit is supplied as VAV box only. Controller & actuator shall be provided by the contractor.
View Product Datasheet
-
Single Deflection Grilles (Mo...
Finish: Powder coated to RAL 9010 as standard. Other finish is available as option.
JMC Grilles and Registers have adjustable louvers and are available in single deflection models. The Single deflection grilles are designed to have one set of blades in the horizontal or vertical orientation. Air pattern is adjustable in one plane only. The Horizontal type provides the control over the deflection of the air pattern on adjustments whereas the vertical type provides the spread control of the air pattern reducing both throw and drop.
View Product Datasheet
QR 12.00 – QR 94.00View Options -
Sand Louvers Model KSTL
The Sand Trap Louvers Model KSTL are designed for usage in serving as a Pre – Filter element in dusty conditions. It has a degree of separation of sand and large dust particles, even in cases of high dust concentrations. The vertically arranged sections and holes for sand drainage ensure the sand trap louver is self- cleaning and maintenance free. The sand trap louver is designed to separate large particles at low air velocities, thus avoiding excessive dust loading on conventional plant filters. It is not intended as a substitute for conventional supply air filtration.
View Product Datasheet
-
Egg Crate Grilles (Model: KECG)
Finish: Powder coated to RAL 9010 as standard. Other finish is available as option.
JMC Return / Exhaust Grilles utilize core of cubical grid and mostly used where maximum free area is desired and “see through” is not a concern. These Grilles are typically used in ceiling applications where “see through” sight lines are minimized to directly below the grille. Recommended for general return or exhaust of room air.
View Product Datasheet
QR 28.00 – QR 233.00View Options -
Door Grille (Model: XNSA)
Finish: Powder coated to RAL 9010 as standard. Other finish is available as option.
KMC air transfer Grilles or Door grilles are typically used indoors and partitions to allow airflow to a space that is not directly served by a ducted source of supply air or a ducted outlet for return or exhaust air. These Door / Wall Grilles offer the largest free area possible with a complete sight proof or lightproof core.
View Product Datasheet
QR 32.00 – QR 210.00View Options -
Spot Diffuser (Model: SPD)
Finish: Powder coated to RAL 9010 as standard. Other finish is available as option.
KMC Spot diffusers are recommended for use in large spaces such as malls, exhibit hall, etc., Where directional control of conditioned air is of very much importance. The adjustable nozzle models make it possible to adapt the jet discharge angle to suit different operating conditions.
View Product Datasheet
-
Jet Diffuser (Model: KDJ)
Finish: Powder coated to RAL 9010 as standard. Other finish available as option.
JMC Jet diffuser is a high capacity diffuser with jet-type airflow specifically designed for spot heating or cooling in high ceiling applications. The elegant design is best suited for an architectural high-end appearance and provides a modern alternative to any traditional diffusers while upholding the trusted performance characteristics.
View Product Datasheet
QR 234.00 – QR 1,496.00View Options -
Cylinder Mounting Bracket
Vertical bracketing of the PCL-160, PCL-300 and PCL-460 is provided by the Model MB-15 bracket kit . Vertical bracketing of the PCL-600 is provided by the Model MB-1 bracket kit . These kits must be ordered separately with each cylinder/valve assembly. Cylinder installation instructions are provided in the installation section of this manual.
- Cylinder Bracket
- These kits must be ordered separately with each cylinder/valve assembly
- Cylinder installation instructions are provided in the installation section of this manual.
View Product Datasheet
-
Nozzle
Nozzles have been developed for appliance, plenum, and duct applications. All nozzles have a specific flow point value and are supplied with metal blow-off caps to prevent clogging. Each nozzle is stamped with the model number.
View Product Datasheet
-
Agent Cylinder With Valve
The cylinder is manufactured, tested, and meets DOT requirements. Cylinders come pre-filled with extinguishing agent and are charged with dry nitrogen to a pressure
- Meets the requirements of the Building Officials and Code Administrators (BOCA)
- Meets the requirements of the International Building Code (IBC)
- Approved by the City of New York Material and Equipment
View Product Datasheet
QR 2,445.00View Options -
Duct Access Door (Model: AD*)
Duct access doors are manufactured in accordance to SMACNA standard using high quality materials to provide access for life safety damper inspection, controls adjusting, and many other applications in HVAC ducts.
View Product Datasheet
QR 31.03 – QR 102.85View Options -
Linear Slot Diffuser (Model:...
Finish: Powder coated to RAL 9010 as standard. Other finish is available as option.
Linear Slot Diffusers manufactured by KMC have been designed to satisfy architectural concepts that require continuous length applications without compromising air distribution performance. These diffusers utilizes an adjustable vane in each slot to control the direction of air discharge either parallel with or perpendicular to its face surface. The adjustment from the face of the diffuser allows for pattern control in a full 180 degree range for either right or left parallel, intermediate or perpendicular
View Product Datasheet
QR 44.80 – QR 318.56View Options -
Double Deflection Grilles (M...
Finish: Powder coated to RAL 9010 as standard. Other finish is available as option.
KMC supply Grilles and Registers have adjustable louvers and are available in double deflection models. The Double deflection grilles are designed to have two sets of blades in both the horizontal or vertical orientation with air pattern being adjustable in both horizontal and vertical planes. Adjustment of the Horizontal blades provides the control over the deflection of the air pattern. Adjustment of the vertical blades provides the spread control of the air pattern, reducing both throw and drop.
View Product Datasheet