-
Mounting Feet
To fasten the fan on the floor or to the ceiling. Manufactured in steel sheet and protected against atmospheric agents by epoxy paint.
View Product Datasheet
-
Centrifugal Fans – Forw...
The fans of the AL series find their principal application in the civil and industrial ventilation plants, heating and conditioning.
View Product Datasheet
QR 5,260.00View Options -
Centrifugal In-Line Fans Roun...
The AXC LINE-METAL is a series of centrifugal in-line fans with the advantage, typical of axial fans, to convey air along the same axis of the impeller
View Product Datasheet
QR 588.00 – QR 646.00View Options -
Plate Mounted Axial Fans
The QCM series are axial fans suitable for application on wall or panel in residential, commercial and industrial building.
View Product Datasheet
-
Gravity Shutters
Gravity Shutters avoids heat loss and entry of wind, rain, and birds. The fins of the shutter are opened by the airflow when the fan is working and they close down by gravity when the fan is switched off.
View Product Datasheet
QR 302.00 – QR 485.00View Options -
-
Centrifugal Inline Fans
The TMF is a series of centrifugal in-line fans with the advantage, typical of axial fans, to convey air along the same axis of the impeller. The low noise level and the good pressure head make them ideal for industrial and residential installations. They are suitable to convey clean air up to a maximum temperature of 40°C.
View Product Datasheet
QR 490.00View Options -
Rubber Support Inserts
Used at the supporting points of insulated pipes to prevent crushing of insulation. Available with steel reinforcements for larger sizes. Inherently superior to wood .
View Product Datasheet
QR 1.46 – QR 131.31View Options -
U Strap With EPDM Lining
A Standard Pipe Strap with lining is recommended for supporting a piping system with fittings vertically or horizontally to walls or ceilings. It can be used as a restrainer when installed on top of structural wood beams for beam, for limiting pipe movements due to thrust loads during sprinkler system start-up.
View Product Datasheet
QR 1.59 – QR 10.29View Options -
U Strap
A Standard Pipe Strap is recommended for supporting a piping system with fittings vertically or horizontally to walls or ceilings. It can be used as a restrainer when installed on top of structural wood beams for beam, for limiting pipe movements due to thrust loads during sprinkler system start-up.
View Product Datasheet
QR 2.40 – QR 9.00View Options -
U Bolts with Lining
U-Bolts with lining are used to secure piping to structural members.
QR 3.22View Options -
U Bolt with 4 nuts
U-Bolts are used to secure piping to structural members.
View Product Datasheet
QR 2.40 – QR 10.55View Options -
Clevis Hanger
A Clevis Hanger provides for sizeable loads to be supported and for an elevation adjustment depending upon the pipe diameter. The lower nut adjusts the piping to the proper elevation and the upper nut, when locked into position, prevents loosening due to vibration.
View Product Datasheet
QR 1.63 – QR 20.93View Options -
Sprinkler Pipe Hanger
A Sprinkler Hanger recommended to provide vertical support to non insulated piping systems. By adjusting the position of the sprinkler nut on the hanger rod at the top of the hanger, pipe elevation can be altered.
View Product Datasheet
QR 0.99 – QR 5.71View Options -
Pipe Hanger with EPDM Lining
PIPE HANGER WITH EPDM LINING is recommended for non-insulated stationary pipelines in a horizontal position. It can be used for supporting pipes along with the roof.
View Product Datasheet
QR 0.65 – QR 3.28View Options -
Centrifugal Roof Extractors
Centrifugal roof fans are designed for direct or ducted ventilation in residential, commercial, and industrial buildings. they are designed for easy installation, high-efficiency low noise levels. The motor is outside the airflow, this allows the fan to exhaust clean or slightly dusty air with temperature
View Product Datasheet
-
Inlet Cone
It allows a higher fan efficiency in case of installation with an inlet or outlet not ducted. Manufactured in steel sheet, with one flange according to UNI ISO6580 – EUROVENT to be fitted to the CC fan, and an aerodynamically shaped bell mouth, with fixing holes for a protection guard Protected against atmospheric agents by epoxy paint.
View Product Datasheet
QR 1,365.00View Options -
Ultra-Slim Wall Axial Fans
To exhaust air directly to the outside or into a short length ducting (max 3 m length). Suitable for toilets, bathrooms, WC’s, shower-rooms, utility rooms, and kitchens
View Product Datasheet
QR 176.00 – QR 346.00View Options -
GRID SS-BOX 315, PROTECTION G...
Main structure in galvanized steel sheet, inside lined with extra-thick acoustic insulation to minimize noise and ensure the silence of fan operation when placed inside.
SS-BOXED fans are suitable for being installed in small exhausting plants, where limited dimensions and easy installation are also required.
View Product Datasheet
QR 110.00 – QR 125.00View Options