-
OS and Y Gate Valves
Mueller 2300 Series Resilient Wedge Gate Valves are intended for use in potable water distribution or fire protection systems.
- UL 262 Listed and FM 1120/1130 Approved and certified to ANSI/NSF 61 & 372
- Epoxy Coated interior and exterior surfaces
- Outside Screw & Yoke (O.S.&Y)
- Adjustable packing
- Rubber encapsulated iron wedge
- Hand wheel – open left or open right
View Product Datasheet
QR 1,180.00View Options -
Mounting Feet
To fasten the fan on the floor or to the ceiling. Manufactured in steel sheet and protected against atmospheric agents by epoxy paint.
View Product Datasheet
View Options -
Centrifugal In-Line Fans Roun...
The AXC LINE-METAL is a series of centrifugal in-line fans with the advantage, typical of axial fans, to convey air along the same axis of the impeller
View Product Datasheet
QR 588.00View Options -
Gravity Shutters
Gravity Shutters avoids heat loss and entry of wind, rain, and birds. The fins of the shutter are opened by the airflow when the fan is working and they close down by gravity when the fan is switched off.
View Product Datasheet
View Options -
-
Centrifugal Inline Fans
The TMF is a series of centrifugal in-line fans with the advantage, typical of axial fans, to convey air along the same axis of the impeller. The low noise level and the good pressure head make them ideal for industrial and residential installations. They are suitable to convey clean air up to a maximum temperature of 40°C.
View Product Datasheet
View Options -
Rubber Support Inserts
Used at the supporting points of insulated pipes to prevent crushing of insulation. Available with steel reinforcements for larger sizes. Inherently superior to wood .
View Product Datasheet
QR 1.46 – QR 131.31View Options -
U Strap With EPDM Lining
A Standard Pipe Strap with lining is recommended for supporting a piping system with fittings vertically or horizontally to walls or ceilings. It can be used as a restrainer when installed on top of structural wood beams for beam, for limiting pipe movements due to thrust loads during sprinkler system start-up.
View Product Datasheet
QR 1.59 – QR 10.29View Options -
U Strap
A Standard Pipe Strap is recommended for supporting a piping system with fittings vertically or horizontally to walls or ceilings. It can be used as a restrainer when installed on top of structural wood beams for beam, for limiting pipe movements due to thrust loads during sprinkler system start-up.
View Product Datasheet
QR 2.40 – QR 9.00View Options -
U Bolts with Lining
U-Bolts with lining are used to secure piping to structural members.
QR 3.22View Options -
U Bolt with 4 nuts
U-Bolts are used to secure piping to structural members.
View Product Datasheet
QR 2.40 – QR 10.55View Options -
Clevis Hanger
A Clevis Hanger provides for sizeable loads to be supported and for an elevation adjustment depending upon the pipe diameter. The lower nut adjusts the piping to the proper elevation and the upper nut, when locked into position, prevents loosening due to vibration.
View Product Datasheet
QR 1.63View Options -
Sprinkler Pipe Hanger
A Sprinkler Hanger recommended to provide vertical support to non insulated piping systems. By adjusting the position of the sprinkler nut on the hanger rod at the top of the hanger, pipe elevation can be altered.
View Product Datasheet
QR 0.99 – QR 5.71View Options -
Pipe Hanger with EPDM Lining
PIPE HANGER WITH EPDM LINING is recommended for non-insulated stationary pipelines in a horizontal position. It can be used for supporting pipes along with the roof.
View Product Datasheet
QR 0.65 – QR 3.28View Options -
Ultra-Slim Wall Axial Fans
To exhaust air directly to the outside or into a short length ducting (max 3 m length). Suitable for toilets, bathrooms, WC’s, shower-rooms, utility rooms, and kitchens
View Product Datasheet
QR 176.00 – QR 346.00View Options