-
U Strap
Material: Steel
Function: Designed for supporting pipe runs from strut supports.
Approvals: Underwriters Laboratories Listed for B2400-3/4″ thru B2400-8″. Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 26 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 26.
Finish: Electro-Galvanized.View Product Datasheet
View Options -
OS and Y Gate Valves
Mueller 2300 Series Resilient Wedge Gate Valves are intended for use in potable water distribution or fire protection systems.
- UL 262 Listed and FM 1120/1130 Approved and certified to ANSI/NSF 61 & 372
- Epoxy Coated interior and exterior surfaces
- Outside Screw & Yoke (O.S.&Y)
- Adjustable packing
- Rubber encapsulated iron wedge
- Hand wheel – open left or open right
View Product Datasheet
QR 1,180.00View Options -
Mounting Feet
To fasten the fan on the floor or to the ceiling. Manufactured in steel sheet and protected against atmospheric agents by epoxy paint.
View Product Datasheet
View Options -
Centrifugal In-Line Fans Roun...
The AXC LINE-METAL is a series of centrifugal in-line fans with the advantage, typical of axial fans, to convey air along the same axis of the impeller
View Product Datasheet
QR 588.00View Options -
Gravity Shutters
Gravity Shutters avoids heat loss and entry of wind, rain, and birds. The fins of the shutter are opened by the airflow when the fan is working and they close down by gravity when the fan is switched off.
View Product Datasheet
View Options -
-
Centrifugal Inline Fans
The TMF is a series of centrifugal in-line fans with the advantage, typical of axial fans, to convey air along the same axis of the impeller. The low noise level and the good pressure head make them ideal for industrial and residential installations. They are suitable to convey clean air up to a maximum temperature of 40°C.
View Product Datasheet
View Options -
Band Hanger
Material: Steel, Pre-Galvanized to G90 specifications
Function: For fire sprinkler and other general piping purposes. Knurled swivel nut design permits hanger adjustment after installation.View Product Datasheet
QR 1.00 – QR 16.65View Options -
Extention Split Pipe Clamp
Material: Malleable Iron
Function: Designed for suspending non-insulated pipe horizontally or vertically.
Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 25 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 12.
Standard Finish: Plain or Electro-Galvanized.View Product Datasheet
QR 3.85 – QR 26.50View Options -
Rubber Lined Split Clamp
Standard finish: Electro-zinc plated complies with ASTM B633
Function: Designed for suppressing vibration and soundView Product Datasheet
QR 1.27 – QR 5.44View Options -
U Bolt with 4 nuts
Heavy-duty U-Bolts designed to grip, guide or support plain and insulated pipes. Supplied complete with four nuts
View Product Datasheet
View Options -
Riser Clamp
A Riser clamp is a type of hardware used by mechanical building trades for pipe support in vertical runs of piping (risers) at each floor level. The devices are placed around the pipe and integral fasteners are then tightened to clamp them onto the pipe.
View Product Datasheet
QR 14.30 – QR 131.00View Options -
Short Insulation Protection S...
Function: Designed for protection of foam, fiberglass, or any high density insulation when used with pipe hangers.
Finish: Pre-GalvanizedView Product Datasheet
QR 5.70 – QR 14.50View Options -
Cleivis Hanger
A Clevis Hanger provides for sizeable loads to be supported and for an elevation adjustment depending upon the pipe diameter. The lower nut adjusts the piping to the proper elevation and the upper nut, when locked into position, prevents loosening due to vibrati
View Product Datasheet
QR 2.86 – QR 99.50View Options -
Ultra-Slim Wall Axial Fans
To exhaust air directly to the outside or into a short length ducting (max 3 m length). Suitable for toilets, bathrooms, WC’s, shower-rooms, utility rooms, and kitchens
View Product Datasheet
QR 176.00 – QR 346.00View Options