-
U Strap
Material: Steel
Function: Designed for supporting pipe runs from strut supports.
Approvals: Underwriters Laboratories Listed for B2400-3/4″ thru B2400-8″. Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 26 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 26.
Finish: Electro-Galvanized.View Product Datasheet
QR 37.80 – QR 44.80View Options -
Mounting Feet
To fasten the fan on the floor or to the ceiling. Manufactured in steel sheet and protected against atmospheric agents by epoxy paint.
View Product Datasheet
-
Centrifugal Fans – Forw...
The fans of the AL series find their principal application in the civil and industrial ventilation plants, heating and conditioning.
View Product Datasheet
QR 5,260.00View Options -
Centrifugal In-Line Fans Roun...
The AXC LINE-METAL is a series of centrifugal in-line fans with the advantage, typical of axial fans, to convey air along the same axis of the impeller
View Product Datasheet
QR 588.00 – QR 646.00View Options -
Plate Mounted Axial Fans
The QCM series are axial fans suitable for application on wall or panel in residential, commercial and industrial building.
View Product Datasheet
-
Gravity Shutters
Gravity Shutters avoids heat loss and entry of wind, rain, and birds. The fins of the shutter are opened by the airflow when the fan is working and they close down by gravity when the fan is switched off.
View Product Datasheet
QR 302.00 – QR 485.00View Options -
-
Centrifugal Inline Fans
The TMF is a series of centrifugal in-line fans with the advantage, typical of axial fans, to convey air along the same axis of the impeller. The low noise level and the good pressure head make them ideal for industrial and residential installations. They are suitable to convey clean air up to a maximum temperature of 40°C.
View Product Datasheet
QR 490.00View Options -
Band Hanger
Material: Steel, Pre-Galvanized to G90 specifications
Function: For fire sprinkler and other general piping purposes. Knurled swivel nut design permits hanger adjustment after installation.View Product Datasheet
QR 1.00 – QR 16.65View Options -
Extention Split Pipe Clamp
Material: Malleable Iron
Function: Designed for suspending non-insulated pipe horizontally or vertically.
Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 25 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 12.
Standard Finish: Plain or Electro-Galvanized.View Product Datasheet
QR 3.85 – QR 26.50View Options -
Rubber Lined Split Clamp
Standard finish: Electro-zinc plated complies with ASTM B633
Function: Designed for suppressing vibration and soundView Product Datasheet
QR 1.27 – QR 5.44View Options -
U Bolt with 4 nuts
Heavy-duty U-Bolts designed to grip, guide or support plain and insulated pipes. Supplied complete with four nuts
View Product Datasheet
QR 9.60 – QR 256.00View Options -
Riser Clamp
A Riser clamp is a type of hardware used by mechanical building trades for pipe support in vertical runs of piping (risers) at each floor level. The devices are placed around the pipe and integral fasteners are then tightened to clamp them onto the pipe.
View Product Datasheet
QR 14.30 – QR 131.00View Options -
Short Insulation Protection S...
Function: Designed for protection of foam, fiberglass, or any high density insulation when used with pipe hangers.
Finish: Pre-GalvanizedView Product Datasheet
QR 5.70 – QR 14.50View Options -
Cleivis Hanger
A Clevis Hanger provides for sizeable loads to be supported and for an elevation adjustment depending upon the pipe diameter. The lower nut adjusts the piping to the proper elevation and the upper nut, when locked into position, prevents loosening due to vibrati
View Product Datasheet
QR 2.86 – QR 99.50View Options -
Centrifugal Roof Extractors
Centrifugal roof fans are designed for direct or ducted ventilation in residential, commercial, and industrial buildings. they are designed for easy installation, high-efficiency low noise levels. The motor is outside the airflow, this allows the fan to exhaust clean or slightly dusty air with temperature
View Product Datasheet
-
Inlet Cone
It allows a higher fan efficiency in case of installation with an inlet or outlet not ducted. Manufactured in steel sheet, with one flange according to UNI ISO6580 – EUROVENT to be fitted to the CC fan, and an aerodynamically shaped bell mouth, with fixing holes for a protection guard Protected against atmospheric agents by epoxy paint.
View Product Datasheet
QR 1,365.00View Options -
Ultra-Slim Wall Axial Fans
To exhaust air directly to the outside or into a short length ducting (max 3 m length). Suitable for toilets, bathrooms, WC’s, shower-rooms, utility rooms, and kitchens
View Product Datasheet
QR 176.00 – QR 346.00View Options -
GRID SS-BOX 315, PROTECTION G...
Main structure in galvanized steel sheet, inside lined with extra-thick acoustic insulation to minimize noise and ensure the silence of fan operation when placed inside.
SS-BOXED fans are suitable for being installed in small exhausting plants, where limited dimensions and easy installation are also required.
View Product Datasheet
QR 110.00 – QR 125.00View Options