-
Square Diffusers ( KDF series)
Finish: Powder coated to RAL 9010 as standard. Other finish is available as option.
The performance objective of a ceiling air Diffuser is to deliver conditioned air into an occupied space in a quiet draft free manner. The performance efficiency of a particular diffuser design is usually judged by the diffuser’s ability to rapidly dissipate the air velocities and temperature differential of the supply air before it enters the occupied space. Many Models are developed by KMC to meet air distribution and architectural requirements.
View Product Datasheet
QR 38.00 – QR 90.50View Options -
Hose Male Adaptor
The male pilot hose connector is used to connect two pilot hoses together for systems where a second container of a different size is used to protect a different enclosure.
View Product Datasheet
-
Manual/Pneumatic Actuator
This Actuator is Used for mechanical or pneumatic operating system at the container position and is fitted to the top of the valve assembly or removable electrical actuator.
View product Datasheet
QR 334.00View Options -
Supervisory Pressure Switch
A low pressure warning switch is fitted to every container and must be ordered separately. The device continuously monitors the container pressure and in the event of the pressure dropping below 20 bar (290 psi) the switch operates to enable the condition to be signaled to a control unit
View Product Datasheet
QR 157.00View Options -
Manifold Inlet
Manifold inlets are available for the construction of system manifolds. Threaded Inlet for Manifolds
View Product Datasheet
-
Bladder Expansion Tank
Intended for use in hydronic heating systems, these tanks accept the expanded volume of hot water keeping the system pressure below the relief valve setting, thus preventing dangerous pressure build-up.
View Product Datasheet
QR 12,200.00 – QR 13,500.00View Options -
Valve Single Tank Adaptors
When a single 343 litre container is being used without a manifold, three swivel adaptors are available for connection to the discharge outlet
View Product Datasheet
QR 657.00View Options -
Pressure Independent Control ...
FLOWCON PRESSURE INDEPENDENT CONTROL VALVE, FIXED FEMALE BY FEMALE THREADED, PRESSURE/TEMPERATURE PLUGS (STANDARD) HIGH FLOW
The Flowcon PICV is designed as a 3-in-1 solution combining a full stroke modulation control valve, an automatic balancing valve, and a differential pressure control valve
View Product Datasheet
-
Bye-Pass Assembly
For either system by-pass application, Flowcon recommends a combination of automatic/dynamic balancing and 3-way control with focus on indoor climate and reduced energy consumption FLOWCON FCU LINK WITH BYPASS ISOLATION VALVES, IVC STRAINER, AND FLOWCON PICV FIXED FMXFM WITH P/T PLUGS, SS FLEXIBLE CONNECTOR & INSULATION
View Product Datasheet BY-PASS ASSY
-
Extention Split Pipe Clamp
Material: Malleable Iron
Function: Designed for suspending non-insulated pipe horizontally or vertically.
Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 25 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 12.
Standard Finish: Plain or Electro-Galvanized.View Product Datasheet
-
Rubber Lined Split Clamp
Standard finish: Electro-zinc plated complies with ASTM B633
Function: Designed for suppressing vibration and soundView Product Datasheet
-
U Bolt with 4 nuts
Heavy-duty U-Bolts designed to grip, guide or support plain and insulated pipes. Supplied complete with four nuts
View Product Datasheet
-
Riser Clamp
A Riser clamp is a type of hardware used by mechanical building trades for pipe support in vertical runs of piping (risers) at each floor level. The devices are placed around the pipe and integral fasteners are then tightened to clamp them onto the pipe.
View Product Datasheet
QR 14.30 – QR 131.00View Options -
Short Insulation Protection S...
Function: Designed for protection of foam, fiberglass, or any high density insulation when used with pipe hangers.
Finish: Pre-GalvanizedView Product Datasheet
QR 5.70 – QR 14.50View Options -
Cleivis Hanger
A Clevis Hanger provides for sizeable loads to be supported and for an elevation adjustment depending upon the pipe diameter. The lower nut adjusts the piping to the proper elevation and the upper nut, when locked into position, prevents loosening due to vibrati
View Product Datasheet
QR 2.86 – QR 99.50View Options
- ALL PRODUCTS
- FIRE FIGHTING & FIRE ALARM
- HVAC & PLUMBING
- INSULATION MATERIALS
- AIR OUTLETS & DAMPERS
-
Grilles & Diffusers
- Egg Crate Grilles (Model: KECG)
- Door Grille (Model: XNSA)
- Spot Diffuser (Model: SPD)
- Jet Diffuser (Model: KDJ)
- Linear Slot Diffuser (Model:…
- Double Deflection Grilles (M…
- Exhaust Grilles (Model: KX3HD)
- Circular Diffuser (Model: KCM)
- Disc Valves (Model: KDV)
- Square Diffusers ( KDF series)
- Single Deflection Grilles (Mo…
-
- BROWSE BY BRANDS
-
- RATE US
- POPULAR
BRANDS
-
Refrigeration Copper Coils
Brand: IUSA Cambridge Lee
Copper Pipes & Coils manufactured to ASTM B743 standards are suitable for gas applications and other high-pressure refrigerants.
Buy nowIsoline Pipe InsulationBrand: K-Flex Isoline
Isoline is a high-quality rubber insulation which is a closed-cell tube insulation product used to prevent condensation on piping applications.
Buy nowWall Split Air ConditionerBrand: Ruud
Developed with environment friendly R410A refrigerant. R410A refrigerant is highly efficient and has an Ozone Depletion Potential (ODP) of 0.
Buy now
-