-
Refrigerant Pipe Insulation
Worldflex is a high-quality Class-1 Elastomeric/Rubber Insulation which is a flexible, closed-cell tube insulation product used to conserve energy and prevent condensation on piping applications. The product’s closed-cell structure creates exceptional thermal properties that protect against moisture penetration in refrigeration tubing applications.
Low flame spread: When fire tested, World Flex does not generate flaming droplets and has low flame spread achieving the fire performance of Class 1
Fire: Class 1 BS 476 Pt 7 1997
Ozone Depletion: Zero
HCFC-CFC free
Standard length : 6 FEET LONG CLASS “1” PIPE SECTIONS
Purchased as Box Qty
View Product Datasheet
View Options -
Test and Drain Valve
The test and drain valve complies with NFPA13 sprinkler systems. Inspector’s test and drain unit w/on-off unit with brass sight glass. Female NPT inlet and outlet cast brass valve.
View Product Datasheet
View Options -
Discharge Nozzle Brass
FM-200® is distributed within the protected area by the discharge nozzle which is sized to ensure the correct flow of agent for the risk. Nozzles are supplied as standard in Brass as BSPP or NPT with Stainless Steel as an option
View Product Datasheet
QR 345.00View Options -
Refrigeration Copper Coils
Copper Pipes & Coils manufactured to ASTM B743 standards are suitable for gas applications and other high-pressure refrigerants.
ACR Copper Coils & Pipes are dehydrated, degreased, purged with nitrogen, and capped to maintain the internal cleanliness of the product.
Coil Length: 15 meters
View Product Datasheet
View Options -
Rockwool Slab
KIMMCO Rockwool RB Slabs are semi-rigid and rigid boards manufactured from stable stone fibers bonded with a minimum quantity of thermosetting resin binder
View Product Datasheet
QR 20.00View Options -
Cylinder Mounting Bracket
Vertical bracketing of the PCL-160, PCL-300 and PCL-460 is provided by the Model MB-15 bracket kit . Vertical bracketing of the PCL-600 is provided by the Model MB-1 bracket kit . These kits must be ordered separately with each cylinder/valve assembly. Cylinder installation instructions are provided in the installation section of this manual.
- Cylinder Bracket
- These kits must be ordered separately with each cylinder/valve assembly
- Cylinder installation instructions are provided in the installation section of this manual.
View Product Datasheet
QR 262.00 – QR 275.00View Options -
Nozzle
Nozzles have been developed for appliance, plenum, and duct applications. All nozzles have a specific flow point value and are supplied with metal blow-off caps to prevent clogging. Each nozzle is stamped with the model number.
View Product Datasheet
QR 145.00 – QR 154.00View Options -
Agent Cylinder With Valve
The cylinder is manufactured, tested, and meets DOT requirements. Cylinders come pre-filled with extinguishing agent and are charged with dry nitrogen to a pressure
- Meets the requirements of the Building Officials and Code Administrators (BOCA)
- Meets the requirements of the International Building Code (IBC)
- Approved by the City of New York Material and Equipment
View Product Datasheet
View Options -
Hose Male Adaptor
The male pilot hose connector is used to connect two pilot hoses together for systems where a second container of a different size is used to protect a different enclosure.
View Product Datasheet
QR 43.00View Options -
Manual/Pneumatic Actuator
This Actuator is Used for mechanical or pneumatic operating system at the container position and is fitted to the top of the valve assembly or removable electrical actuator.
View product Datasheet
QR 334.00View Options -
Supervisory Pressure Switch
A low pressure warning switch is fitted to every container and must be ordered separately. The device continuously monitors the container pressure and in the event of the pressure dropping below 20 bar (290 psi) the switch operates to enable the condition to be signaled to a control unit
View Product Datasheet
QR 157.00View Options -
Manifold Inlet
Manifold inlets are available for the construction of system manifolds. Threaded Inlet for Manifolds
View Product Datasheet
QR 382.00View Options -
Wet Chemical Fire Extinguishers
Wet chemical extinguishers are the best restaurant kitchen appliance hand portable fire extinguishers.
- All metal valve construction
- Swivel connection on hose allows nozzle to be oriented for proper use
- Nozzle grip design with 45° angle for easy “overhead” application
- Low PH agent discharged as fine mist helps prevent grease splash and re-flash while cooling the appliance
- Precise extinguishing agent application no dry chemical to clean up
- Excellent for use on all cooking appliances including solid fuel charbroilers
- Tested on commercial deep fat fryers to ul 711 test protocol and safe to use on class c fires
- Class 2a rated to meet fire code occupancy hazard requirements
- Bar coded and bi-lingual labels
View Product Datasheet
QR 280.00View Options -
Valve Single Tank Adaptors
When a single 343 litre container is being used without a manifold, three swivel adaptors are available for connection to the discharge outlet
View Product Datasheet
QR 657.00View Options -
Automatic Heat Detector
Explosion-proof for installation in hazardous locations. Has hexagonal grip bushing with 1/2’ conduit threads for attachment to threaded hub cover of series JL fixture fitting
View Product Datasheet
QR 229.00View Options -
Wet Chemical Fire Extinguishers
Wet Chemical Fire Extinguishers use a film forming base with additional chemicals and micro drop mist nozzle technology. The agent forms a mild foam surface over the hot oil but not a crust or foam mess like most other agents. The extinguishing is through smothering initially and cooling through heat absorption through high volume micro drops and a chemical reaction.
CLASSES OF FIRE
View Product Datasheet
QR 280.00View Options