-
Abort Switch
Single-gang size; includes 3 position contact block housing with 1 contact block UL, ULC, CSFM listed.
View Product Datasheet
QR 381.00View Options -
Basic Control Unit Modules
4010 control panel Basic Control Unit with 2 x 40 LCD Operator Interface and (1) Two-loop Isolated IDNet+ Communications Channel, Class A or Class B operation, with support for up to 248 addressable IDNet points
View Product Datasheet
QR 4,500.00 – QR 5,262.00View Options -
Switch Input Module
These remote annunciator graphic control modules complement Simplex 4007ES, 4010ES, 4100ES, and 4100U (and other installed legacy panels) by providing LED/lamp/relay drivers and switch inputs to allow custom graphic displays to be designed for specific facility requirements, such as for smoke control (UUKL) systems.
View Product Datasheet
View Options -
Multi-Candela Strobes
Multi-candela strobe with intensity selectable as: 15, 30, 75, or 110 candela; synchronized flash rate.
- Simplex fire alarm control panels with NACs selected to provide strobe synchronization or SmartSync two-wire control
- Ceiling mount strobes installed using standard single gang electrical boxes.
- Rear of housing does not extend into box
View Product Datasheet
View Options -
Bladder Expansion Tank
Intended for use in hydronic heating systems, these tanks accept the expanded volume of hot water keeping the system pressure below the relief valve setting, thus preventing dangerous pressure build-up.
View Product Datasheet
QR 12,200.00 – QR 13,500.00View Options -
DZR Brass Float Valve
DZR Brass Float Valve. Supplied with locknut. Machined fixed flange on the valve body. No jam single lever action.
View Product Datasheet
View Options -
Flashing Strobe
TrueAlert ES addressable strobes are individually addressed visible notification appliances that receive power, supervision, and control signals from the Simplex fire alarm control panel providing IDNAC Signaling Line Circuits (SLCs).
View Product Datasheet
View Options -
Extention Split Pipe Clamp
Material: Malleable Iron
Function: Designed for suspending non-insulated pipe horizontally or vertically.
Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 25 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 12.
Standard Finish: Plain or Electro-Galvanized.View Product Datasheet
QR 3.85 – QR 26.50View Options -
Rubber Lined Split Clamp
Standard finish: Electro-zinc plated complies with ASTM B633
Function: Designed for suppressing vibration and soundView Product Datasheet
View Options -
U Bolt with 4 nuts
Heavy-duty U-Bolts designed to grip, guide or support plain and insulated pipes. Supplied complete with four nuts
View Product Datasheet
QR 9.60 – QR 256.00View Options -
Riser Clamp
A Riser clamp is a type of hardware used by mechanical building trades for pipe support in vertical runs of piping (risers) at each floor level. The devices are placed around the pipe and integral fasteners are then tightened to clamp them onto the pipe.
View Product Datasheet
QR 14.30 – QR 131.00View Options -
Short Insulation Protection S...
Function: Designed for protection of foam, fiberglass, or any high density insulation when used with pipe hangers.
Finish: Pre-GalvanizedView Product Datasheet
View Options -
Cleivis Hanger
A Clevis Hanger provides for sizeable loads to be supported and for an elevation adjustment depending upon the pipe diameter. The lower nut adjusts the piping to the proper elevation and the upper nut, when locked into position, prevents loosening due to vibrati
View Product Datasheet
QR 2.86 – QR 99.50View Options