-
U Strap
Material: Steel
Function: Designed for supporting pipe runs from strut supports.
Approvals: Underwriters Laboratories Listed for B2400-3/4″ thru B2400-8″. Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 26 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 26.
Finish: Electro-Galvanized.View Product Datasheet
-
-
Mounting Feet
To fasten the fan on the floor or to the ceiling. Manufactured in steel sheet and protected against atmospheric agents by epoxy paint.
View Product Datasheet
-
Pressure Independent Control ...
FLOWCON PRESSURE INDEPENDENT CONTROL VALVE, FIXED FEMALE BY FEMALE THREADED, PRESSURE/TEMPERATURE PLUGS (STANDARD) HIGH FLOW
The Flowcon PICV is designed as a 3-in-1 solution combining a full stroke modulation control valve, an automatic balancing valve, and a differential pressure control valve
View Product Datasheet
-
Centrifugal In-Line Fans Roun...
The AXC LINE-METAL is a series of centrifugal in-line fans with the advantage, typical of axial fans, to convey air along the same axis of the impeller
View Product Datasheet
QR 372.00View Options -
Plate Mounted Axial Fans
The QCM series are axial fans suitable for application on wall or panel in residential, commercial and industrial building.
View Product Datasheet
QR 2,487.00 – QR 2,896.00View Options -
Gravity Shutters
Gravity Shutters avoids heat loss and entry of wind, rain, and birds. The fins of the shutter are opened by the airflow when the fan is working and they close down by gravity when the fan is switched off.
View Product Datasheet
-
-
Centrifugal Inline Fans
The TMF is a series of centrifugal in-line fans with the advantage, typical of axial fans, to convey air along the same axis of the impeller. The low noise level and the good pressure head make them ideal for industrial and residential installations. They are suitable to convey clean air up to a maximum temperature of 40°C.
View Product Datasheet
-
Band Hanger
Material: Steel, Pre-Galvanized to G90 specifications
Function: For fire sprinkler and other general piping purposes. Knurled swivel nut design permits hanger adjustment after installation.View Product Datasheet
-
Extention Split Pipe Clamp
Material: Malleable Iron
Function: Designed for suspending non-insulated pipe horizontally or vertically.
Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 25 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 12.
Standard Finish: Plain or Electro-Galvanized.View Product Datasheet
QR 3.85 – QR 26.50View Options -
Rubber Lined Split Clamp
Standard finish: Electro-zinc plated complies with ASTM B633
Function: Designed for suppressing vibration and soundView Product Datasheet
QR 1.27 – QR 5.44View Options -
U Bolt with 4 nuts
Heavy-duty U-Bolts designed to grip, guide or support plain and insulated pipes. Supplied complete with four nuts
View Product Datasheet
-
Riser Clamp
A Riser clamp is a type of hardware used by mechanical building trades for pipe support in vertical runs of piping (risers) at each floor level. The devices are placed around the pipe and integral fasteners are then tightened to clamp them onto the pipe.
View Product Datasheet
QR 14.30 – QR 131.00View Options -
Short Insulation Protection S...
Function: Designed for protection of foam, fiberglass, or any high density insulation when used with pipe hangers.
Finish: Pre-GalvanizedView Product Datasheet
QR 5.70 – QR 14.50View Options -
Centrifugal Roof Extractors
Centrifugal roof fans are designed for direct or ducted ventilation in residential, commercial, and industrial buildings. they are designed for easy installation, high-efficiency low noise levels. The motor is outside the airflow, this allows the fan to exhaust clean or slightly dusty air with temperature
View Product Datasheet
QR 2,296.00View Options -
Inlet Cone
It allows a higher fan efficiency in case of installation with an inlet or outlet not ducted. Manufactured in steel sheet, with one flange according to UNI ISO6580 – EUROVENT to be fitted to the CC fan, and an aerodynamically shaped bell mouth, with fixing holes for a protection guard Protected against atmospheric agents by epoxy paint.
View Product Datasheet
QR 540.00View Options -
Ultra-Slim Wall Axial Fans
To exhaust air directly to the outside or into a short length ducting (max 3 m length). Suitable for toilets, bathrooms, WC’s, shower-rooms, utility rooms, and kitchens
View Product Datasheet
QR 95.00 – QR 194.00View Options
- ALL PRODUCTS
- FIRE FIGHTING & FIRE ALARM
- HVAC & PLUMBING
- INSULATION MATERIALS
- AIR OUTLETS & DAMPERS
-
Grilles & Diffusers
- Egg Crate Grilles (Model: KECG)
- Door Grille (Model: XNSA)
- Spot Diffuser (Model: SPD)
- Jet Diffuser (Model: KDJ)
- Linear Slot Diffuser (Model:…
- Double Deflection Grilles (M…
- Exhaust Grilles (Model: KX3HD)
- Circular Diffuser (Model: KCM)
- Disc Valves (Model: KDV)
- Square Diffusers ( KDF series)
- Single Deflection Grilles (Mo…
-
- BROWSE BY BRANDS
-
- RATE US
- POPULAR
BRANDS
-
Refrigeration Copper Coils
Brand: IUSA Cambridge Lee
Copper Pipes & Coils manufactured to ASTM B743 standards are suitable for gas applications and other high-pressure refrigerants.
Buy nowIsoline Pipe InsulationBrand: K-Flex Isoline
Isoline is a high-quality rubber insulation which is a closed-cell tube insulation product used to prevent condensation on piping applications.
Buy nowWall Split Air ConditionerBrand: Ruud
Developed with environment friendly R410A refrigerant. R410A refrigerant is highly efficient and has an Ozone Depletion Potential (ODP) of 0.
Buy now
-